EPDM Porch Roof Kits
Flat Roof Kits for porches where the long edge has a gutter and the other long edge a wall flashing adjoining the house wall.
Please select correct size kit from the drop-down. If you need a different trim configuration please use the ClassicBond Kit Calculator from the menu.
EPDM Porch Roof Kits
These ClassicBond EPDM Porch Roof Kits are designed for structures where the gutter is along the front edge (Width) and the back edge adjoins a house wall. Kerb Edge trims are provided for the two remaining sides (Depth). The kits are easy to install, look great and have a life expectancy of up to 50 years! EPDM rubber membranes are UV, Ozone and Infra red stable so will not crack, blister or peel.
We have put together these Porch Roof Kits to including the 1.2mm One-Piece EPDM rubber membrane, adhesives, edging trims and tools required to complete this DIY project.
Included in Kit:
- 1.2mm ClassicBond EPDM Membrane (Size per roof kit chosen)
- Water Based Adhesive to adhere Membrane to roof deck
- Contact adhesive to adhere Perimeter of roof deck to Membrane
- Sure Edge Gutter for front edge
- Sure Edge Kerb for both side edges
- Sure Edge Corner for both front corners
- Wall trim to act as flashing against your house wall
- External corner Patches & Primer fo both back corners where roof meets house wall
- Tools requires for DIY Installation(Rollers, Scissors & Paint Brush)
- All Pins and Clips to go with Trims
- Installation Guide
WE CAN TAILOR THE KIT TO SUIT YOUR ROOF - CALL 0800 313 4486 TO DISCUSS
The Membrane size will be the same as the kit size. Therefore your roof size will need to be smaller to allow for edge overlaps. e.g. 6metre x 3metre roof kit will fit a roof that is no larger than 5.7metres x 2.7metres.
|Stock Type||In Stock|
|Delivery Lead Time||1 Working Day|
EPDM Rubber roofs have a 50 year life expectancy.
EPDM has been in commercial use since the 1960s. And many of those roofs are still around today.
All membranes do have manufactures joins as supplied to us. Depending on the spacing of the joins and the size of
the piece being cut off the roll sometimes there is no manufacturers
join in the membrane.
All EPDM membranes whether it is Firestone,
ClassicBond or SKYGUARD have these joins and they are unavoidable,
however, the big advantage is that it is supplied to you in one piece
as our website states which means you don't have to do any onsite
joins where workmanship could be a factor.
ClassicBond Roof membranes are available in two thicknesses. The Standard membrane is 1.2mm thick and the Premium membranes is 1.5mm
EPDM membranes can be installed onto a veriety of surfaces. For best results we recommend that the membrane be laid onto new Timber sheets (OSB3). This fresh new deck can however be laid stright over your existing roof covering without the need to strip the old roof .
Yes, EPDM Membranes require the substrate to be dry prior to installation. This is so the the adhesive & primers can effectively bond the rubber to roof deck. EPDM products will not adhere to wet or damp surfaces. Trapped moisture may vaporize and negatively affect the performance of the membranes.
Yes, ClassicBond membrane holds the British Board of Agrément certificate, No. 11/4853 (issued to Flex-R Ltd). It also holds fire ratings for each of the thicknesses available.
Classicbond EPDM membranes are identical on both sides so there is no right or wrong side when installing.
However you may sometimes find a small amount of writing printed on one side of the Rubber Membrane. It may be wise to keep this side down so an eyesore is not created.
We recommentd a minimum tempereture of 5 degrees C for EPDM installation. This is due the the WBA adhesive being water based and lower temperetures may cause the adhesive to freeze over and fail.